DIY Sex Machine: How To Build A Fucking Machine At Home

In this guide, we are going to look at the cost, parts, and how to actually build your first DIY sex machine.

DIY sex machine

Now, you have this great urge to own a nice and functioning DIY sex machine.

But you haven’t got the slightest clue where to get the parts. How to identify the best designs. Or where to begin when tying up the components.

If the bill above fits you, then you’re in for a treat. Stick around and get to know how to make a fuck machine at home.

So let’s jump right into it:

How Much Will it Cost?

The answer depends on the deepness of your pocket and how much you are willing to spend.

This is because there are myriads of parts’ options you could use in the assembly. And each one comes with a different price, depending on your location.

That said. You could DIY yourself one for as low as $150, or go to upwards of over $1,200.

Which Parts Will You Need?

Before we set the ball rolling, here’s a basic list of parts that you need to have. You can find or improvise some of them from your household electronics or garage.

They include:

  • Motor – We went with a wiper motor (12V) because it’s accessible. It’s whirring is a bit loud but good background music drowns it like magic. ($45 – $150)
  • Speed Controller – You should get one with a range of 9-60 DC volts that can sustain a motor within the same range ($25)
  • Power Supply – For our 12V motor, in this case, a 5 to 6A PSU serves the purpose. ($10)
  • Casing – Our base’s measurements here is 24” x 9.5”. Measurement for the vertical boards holding the motor and shafts may vary. It depends on the size of the motor and shafts used. ($10)
  • A rod with Vac-U-lock attachment – The rods provide the length of the stroke. You will adjust these according to the length that best suits you. Vac-U-lock attachments are available in most retails and you will need to attach one at the end of one rod’s length. ($10)
  • Ways to tie it all together – You need screws, bolts, nuts, air tube connectors, thread ball joints, winding ball joints, rigid shaft couplers, and miscellaneous rod parts to cover for any adjustments in your perfect DIY fuck machine. ($25)

How To Build Your Own Fucking Machine?

There are a few ingenious ways around this.

You have to keep in mind that while it’s more affordable to make it yourself, it’s not going to be as pretty as the ones in the stores. 

Let’s jump right in:


  • Use a 25mm long joint nut of 8mm that fits with an 8mm rotating arm screw. The stroke length is also the length of the arm and should give room for easy adjustments.
  • Attach a ball-joint of a similar threaded 8mm rod at the end of the arm’s length. 
  • Connect the arm to the stroking shaft using a shaft joint, 8mm holes, and matching screws.

N/B: It’s important to mount the shaft’s bearing to prevent the joints from crashing.

  • You need to extend the shafts as they are about 11.8”-12” by default. A simple solution here is a drill length extension that you can fit on the shaft by filing down one end.
  • The most suitable way to join these components is through a set of air tube connectors. This is because their female ends are an easy fit on the shaft with the help of tapes. 
  • The air tube connector’s male part mounts on the suction flat plate or a vac-u-lock adapter.

Simply put, these simple steps will help you close the deal on how to make a homemade fuck machine. Check this tutorial for more detail.

Option #2: The Simplified Sex Machine Design

  • Get the $50 drill from your local hardware store and a piece of timber for the base. The measurements for the timber base piece are 24″ length and 9 1/2″ width.
  • Next, you’ll need another piece of timer for the flywheel that you will connect with the drill, and it’ll move the rod with a dildo. The size of the circle will determine the stroke length, so choose the size you’d like. 
  • Then it’s time to connect the drill and speed controller with the base and the flywheel. After, add your rod with Vac-U-lock attachment. 
  • Using the linear guides, connect your rod to the base, and here you have your structure. 

This is a very basic way to build a DIY sex machine that will do the job.

The speed controller will allow you to choose how hard or soft you want the strokes to be, so you have full control of the experience. 

Sites That Help You With Plans, Tutorials And Sell Parts

Still, stuck? Check out these sites that offer help on assembling, designing, and parts’ listings.

Machine Yourself

This site offers one of the cheapest ways to build a DIY sex machine right off the bat. The Heavy Duty piece only cost $150 and has parts that comprise of:

  • Speed control device @ $25.
  • Harbor Freight drill @ $45.
  • Delrin bought from eBay @ $25
  • Wooden 16” by 3” sheet, ½” thick @ $10
  • Bolts, screws, miscellaneous rod parts, etc. @ $25
  • Aluminum tube that’s 3’ of ¾” @ $10


  1. You mount the drill using the holes in its casing. Bearing in mind the measurements of the flywheel determines the mount’s height.
  2. Make a flywheel from a thick oak board ¾” thick by cutting an 8” circle that provides an equal length in the stroke. This length varies by drilling extra holes in an arc from the center in 1” intervals.
  3. Counter-drill the back of the flywheel to host male ends of the ball joint linkage. The rods aren’t long enough to cover the ¾” board. 
  4. Use a threaded hex standoff with a ¼” bolt for the flywheel’s center post.
  5. To use linear guides, cut them from the Delrin block and fit a ¾” shaft by drilling a ⅞” hole on it. Take note of the plastic heats and shrinks during and after drilling. Maintaining extra ⅛” allows easy linear action.

Watch the full DIY video tutorial here.


This site is a one-stop-shop for DIY sex machine gears. The top ones include:

  • Detachable hand control ($30) 
  • Complete power lines ($120)
  • Locking joint systems ($40)
  • A vast listing of motors


It has a neat documentation of how to build the LoveMachine42People. It gives a detailed step-by-step walkthrough that includes the coding spec of the sex machine.

Hismith gives the best deals on three crucial parts:

  1. Speed controller (Wired/Remote)
  2. A powerful motor (24V/100W)
  3. Power supply compatible with the motor.

Use HSM10 code to get 10% off + free spring attachment from purchase.

Other People’s Sex Machine Building Experiences

And now let’s check what other people are saying about the topic:

“I’ve thought about this for a long time and its DOABLE but honestly you’ll prolly end up paying more in parts and fabrication for something safe and strong enough as you would for a Hi-Smith off Amazon. You can start with a windshield wiper motor and depending on your existing skills and random materials you might be able to get somewhere without spending tons of money, but the motor alone is going to set you back somewhere between $40 and $100 and then you’ve got to figure out a flywheel and a linear drive linkage and a solid base on which to mount everything. . . ”


And here’s another input if you’d like to go a different way:

“I’ve considered using servos, there are cheap servos (£30) that can handle 60-70 kg/cm, and that should be plenty enough for this application. Basically, you wouldn’t go a full rotation, just back and forth, and you can control the position easily in code, and maybe make some “better than real” movement patterns (say, a high frequency, low amplitude wave overlayed on the main wave).

Anyone tried using servos?”


“It’s real simple to make, you need to spin 2-4 poles in an elipse around a mother with movement distance changing with the distance from the mother, find a way to lock pole 3 into 1 dimension of movement and build a case to hold it still, that’s the basic design principal of them

Materials: motor or engine, durable disc or if not possible a mountable pole, 3 metal poles. 2-3 disc hinge if you don’t have one make them by putting 2 discs on a pole and removing as much friction as possible. Screws don’t Know how much you will need. a screw driver or drill.”


Finally, check out this in-depth video where a guy shows how to make a fuck machine:

He says that he builds these sex machines for people, but with the labor and all details, it costs a lot, so if you’re handy, you can follow his tutorial. 

On his Etsy shop, he has fucking machine design plans with the supply lists and everything, and even sells certain parts himself, so it’s worth checking it out. 


There you have it! Before we drop the mic – it’s our hope that the information here was useful in your pursuit of how to build a fucking machine at home (see our best fucking machine review if you want to buy instead).

You finally have knowledge of the cost, plans, and best places to get parts.

You can now make your own piece in the garage

If I were you, I would make the cheaper version of a DIY sex machine with a $50 drill and a few planks of timber. 

You’ll still get a great quality experience, but it won’t hurt your wallet, and you don’t need to become an engineer for that. 

The best thing to do is to check out different communities online that share a lot of great information on building your own DIY fuck machine.

You can get help and advice on the whole building process. 

So, what are you waiting for? GO FOR IT!!

Dainis Graveris

Dainis Graveris

With over 2 year experience working in a local adult toy store Dainis has gathered quite a bit of experience about helping people find the best for their needs. He's also a top writer on Quora (7M views, 2.3K followers) and has written over 70+ guides on SexualAlpha. Read More

Got Questions? Ping me on Twitter.